Incra Intelli-Fence User Manual download pdf (Page 3)

Assemble table clamps

With the table clamps on a flat surface,

insert the (2) #10-32 x

1

/2" phillips pan head

screws through the #10 flat washers then

through the holes in the clamp and loosely

attach the (2) #10-32 hex nuts. See Fig. 5.

Slide the hex nuts into the T-slot in the fence

mounting bracket and tighten the screws.

The ends of the fence mounting bracket

should be flush with the clamp edges.

Repeat for the other clamp.

Attach table clamps to

Intelli-Fence

Position the Intelli-Fence on your router table

with the opening in the fence centered on

your router’s collet. Insert the

1

/4-20 x 2"

socket head cap screws through the

1

/4"

washers then through the fence mounting

bracket and loosely attach the

1

/4-20

rectangular nuts. Now slide the rectangular

nuts into the T-slots on the rear of the

Intelli-Fence. Tighten the clamping knobs to

secure the clamps to the table edge, then

tighten the two socket head cap screws using

the supplied hex key, Fig. 6.

FIG. 5

Assemble table clamps

3

FIG. 4

Attach to your INCRA Jig

MOUNTING TO YOUR ROUTER TABLE

Important: Your INCRA Jig Ultra or Pro must

be mounted to a

3

/4" plywood base and the

carriage clamp must be in the locked position

before installing the Intelli-Fence.

Insert the supplied #10-32 x 1" phillips pan

head screws through the

5

/8" o.d. (gold)

washers then through the holes on the back of

the INCRA Jig Ultra’s fence mounting bracket.

Loosely attach the (2) #10-32 rectangular nuts.

Now slide the rectangular nuts into the T-slot on

the rear of the Intelli-Fence. Position the fence

so that the INCRA Jig’s carriage is

approximately centered on the fence length

and tighten the two mounting screws.

Note: For mounting to the INCRA Jig Pro use

the shorter #10-32 x

1

/2" screws.

Your new INCRA Intelli-Fence can be used

either by clamping directly to your router

table or by attaching first to your INCRA Jig

Ultra or Pro. Mounting directly to your

INCRA Jig adds incremental positioning

1

Freestanding Mode

2

Note: The table clamps are designed to

work on router tables from 1

1

/8" to 1

3

/8" thick.

To increase the thickness of a table less than

1

1

/8" thick, use double faced tape or glue to

attach a wooden strip to the underside of the

table edge.

#10-32 rectangular nut

#10-32 x 1" phillips pan head screw

5

/8" o.d. gold

washer

#10-32 hex nut

Fence

mounting

bracket

#10 flat washer

Table clamp

#10-32 x

1

/2" phillips

pan head screws

By loosening

the two phillips

head screws on

the table clamps

the fence angle

can be adjusted

perfectly square to

your router table.

FIG. 6

Attach table

clamps to

Intelli-Fence

1

/4" flat washer

1

/4 -20 x 2" socket head

cap screw

1

/4 -20 rectangular nut

Attaching to your INCRA Jig Ultra or Pro

control to the already substantial

features of your INCRA Intelli-Fence.

However, if you don’t already own an

INCRA Jig or you just prefer to use the

Intelli-Fence independent of your

INCRA Jig system, the supplied

clamps and instructions below will

allow you to quickly set up and

use the Intelli-Fence in the

freestanding mode.

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments