search

Incra Build-It Starter Kit User Manual Page 5

  • Download
  • Add to my manuals
  • Print
  • Page
    / 6
  • Table of contents
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 4
A
tenoning jig can be an extremely valuable tool at the table saw. Not only does it provide a carrier for narrow pieces when tenoning,
but with the vertical backstop removed, the jig can also be used for raised panel cutting. The sliding base provides plenty of range of
motion for positioning and locating your cuts, while the large 10” x 10” faceplate provides ample support and clamping area for the
largest of panels.
Begin by adding a Miter Slider to a small Build-It Panel. Place in your table saw’s miter slot and adjust for a good fit. If the blade tilts
right, place it in the left hand miter slot. If the blade tilts left, place it in the right hand miter slot. Add a T-Slot Panel Connector to
each edge of the panel. Cut the slotted holes and grooves as shown on the (2) 10” x 10” x 3/4” thick panels. If you are using MDF,
you can cut the grooves with a 3/4” straight bit at your router table. If you are using plywood, remember it is often slightly undersized
so an undersized “plywood bit” is
recommended for the cuts. The depth
of cut should be 1/4” and the fence to bit
distance is 5/8” for
all of the grooves.
Before gluing up
the panels and
braces, drill the
(2) 5/16” dia. holes
in the faceplate
panel. Make the
(2) edge guides as
shown. Attach the first edge guide to
the Build-It Platform and square it to the
edge of the platform. Slide the right angle
assembly up against the edge guide, then
add the other edge guide. Drill and attach
the backstop to finish.
Tenoning Jig
Fig.1 Fig.2
Build-It Platform Components Required:
• 1 Small Build-It Panel • 1 Miter Slider
• 2 T-Slot Panel Connectors
• Build-It Knobs
Just add:
System
it
®
Fig.3
Detail 3A
braces
(
3
/4” stock)
6”
6”
3”
1
1
/2”
1
/4-20 x 2”
hex bolt
12”
4”
4”
faceplate
1
/4-20 x 1
1
/2” (6)
hex bolt
11
1
/2”
8
1
/2”
1
1
/2”
1
3
/4”
7
/8”
10”
10”
8”
1”
Edge guide (
3
/4” stock)
(note: all holes
5
/
16
” dia.)
5
/8”
5
/8”
5
/8”
all grooves
3
/4”
wide x
1
/4”
deep
8” long x
5
/16” wide
slots
backstop
(
3
/4” stock
)
2
1
/2”
4”
4”
2
1
/2”
Plan # 006
Available online at w w w.i n c ra . co m
Page view 4
1 2 3 4 5 6

Comments to this Manuals

No comments
Related products and manuals for Tools Incra Build-It Starter Kit
Tools Incra Build-It Starter Kit User Manual   (6 pages)
Tools Incra Build-It STS Mortiser User Manual   (12 pages)
Tools Incra Build-It Panel User Manual   (4 pages)
Tools Incra Build-It STS Slot Mortiser User Manual   (5 pages)
Tools Incra T-Track Single Track User Manual   (1 pages)
Tools Incra Track & Shop Stop User Manual   (8 pages)
Tools Incra T-Track Plus w/Scale User Manual   (1 pages)
Tools Incra HingeCrafter User Manual   (8 pages)
Tools Incra Miter Channel Glue Down User Manual   (1 pages)
Tools Incra Miter Slider SE User Manual   (1 pages)
Tools Incra Miter Slider User Manual   (8 pages)
  • SERO InSciTek Microsystems DNT VitalWear Lapara
  • Netgear ISDN access devices Brother Cable trays Simrad Navigators Linksys Telephones Craftsman Lawnmowers
  • Whirlpool WFG361LVS Aeg F88400VI0P AEG L9WBC61B Sony HDR-AS100V
  • Morphy Richards 25CG Specifications Zanussi ZDF26020WA User Manual Philips AZ1816/12 User Manual Acer V196WL User Manual Jenn-Air JDTSS244GP Warranty